TEST YOUR KNOWLEDGE.

QUESTION (1) What direction do you turn a distributor to advance the ignition timing?
ANSWER

QUESTION (2) At what speed does the camshaft turn compared to the crankshaft on a single camshaft engine?
ANSWER

QUESTION (3) Name the 4 different strokes of a 4 stroke engine in order, starting from the stroke that carries air into the cylinder.
ANSWER

QUESTION (4) What are the three main purposes of glycol in radiator coolant when mixed at between 30% to 70 % by volume?
ANSWER

QUESTION (5) What action causes a wet liner in a diesel to suffer from erosion?
ANSWER

QUESTION (6) What position on the diesel wet liner is more likely to show evidence of erosion?
ANSWER

QUESTION (7) What side is the thrust side of a cylinder in an engine that turns clockwise if you are looking from the front?
ANSWER

QUESTION (8) What three common methods are used to drive a camshaft?
ANSWER

QUESTION (9) When repairing an engine and a single piston has to be renewed out of a set, what 5 important points must be addressed?
ANSWER

QUESTION (10) What method is necessary to final wash a re-honed bore?
ANSWER

QUESTION (11) What jingle is used as a general rule to determine the direction rings have to be fitted to a piston?
ANSWER

QUESTION (12) How do you calculate the compression ratio of an engine?
ANSWER

QUESTION (13) Super or premium fuel has a higher octane rating than regular fuel, which fuel burns the slowest?
ANSWER

QUESTION (14) If an engine is pinging, would you advance or retard the ignition timing?
ANSWER

QUESTION (15) If you had an engine pinging and the ignition timing was set correctly (including the advance curve), what would be the two most obvious things to check as the possible cause?
ANSWER

QUESTION (16) What does air/fuel ratio represent?
ANSWER

QUESTION (17) What air fuel ratio is required by a petrol engine to achieve perfect combustion?
ANSWER

QUESTION (18) What is the term used to measure combustion quality?
ANSWER

QUESTION (19) What two elements make up all fossil fuels?
ANSWER

QUESTION (20) What is greater, horsepower measured at the flywheel or at the rear wheels? And why?
ANSWER

QUESTION (21) When is manifold vacuum greater, at wide open throttle or at idle?
ANSWER

QUESTION (22) What is the basic difference in operation of a petrol engine and a diesel engine?
ANSWER

QUESTION (23) What does the term "valve- bounce" describe?
ANSWER

QUESTION (24) Why can loose tappets cause valve damage?
ANSWER

QUESTION (25) Why can tight tappets cause burnt valves?
ANSWER

QUESTION (26) Describe the principal behind angle tightening of torque to yield head bolts.
ANSWER

QUESTION (27) What does the term "glazed up bore's" describe and what causes it?
ANSWER

QUESTION (28) What is the clearance between a big-end bearing and the crankshaft referred to as?
ANSWER

QUESTION (29) What causes the problem referred to as "ring spin"?
ANSWER

QUESTION (30) What name is given to compression ring that has the upper face set at an angle and the lower face square?
ANSWER

QUESTION (31) The compression ring described in question 30 is used in some diesel engines. Why is it used in preference to a square shaped ring?
ANSWER

QUESTION (32) What general rule can be applied to rings that fit bore size's 2 inch to 4 inch in regard to minimum "end gap clearance"?
ANSWER

QUESTION (33) The most common cause of engine failures due to faulty workmanship arise from loose nuts and bolts. With this fact in mind what policy should be adopted in regard to the fitting of nuts and bolts?
ANSWER

QUESTION (34) Describe how you would fit a dome welsh plug?
ANSWER

QUESTION (35) What simple rule can be used when selecting the position to adjust valve clearance on the same cylinder?
ANSWER

QUESTION (36) On a test what visual exhaust smoke indicates worn rings? Name the colour and time of emission?
ANSWER

QUESTION (37) In a diesel engine what is usually indicated by the appearance of white exhaust smoke on cold starts?
ANSWER

QUESTION (38) What is the main design difference between a direct injection diesel and an indirect injection diesel?
ANSWER

QUESTION (39) Simply describe the difference between these induction methods (a) normally aspirated. (b) Turbo charged. (c) supercharged.
ANSWER

QUESTION (40) What 2 substances in the cooling system are measured with a chemical tester and gas-analyser to indicate a leakage from combustion to water jacket? ( blown head gasket )
ANSWER

90% to 100% correct answers indicate a good understanding of engine problems and functions. This web site is full of information that may improve your knowledge and skill.

Disclaimer agreement

: Every care has been taken in writing this information and procedures, but no responsibility can be excepted for errors, omissions or misuse of this information and procedures. The information available on this site is for your instruction only and cannot be copied for sale, © copyright 2001 UMR Engines www.engineproblem.com.au